Helmets are round, curved and slippery, which is the entire reason mounting a camera to one is harder than mounting it anywhere else. After working through the mount families ourselves and reading thousands of buyer reviews, the answer is straightforward: the best action camera mount for a helmet is a chin mount for stable POV footage, a clamp mount if you refuse to touch your shell, and a curved adhesive mount if you want a permanent low-profile install. We compared 12 of them for 2026.
This roundup covers every family that matters, including strap chin mounts, gripper clamps, curved adhesive bases and flexible TPU pads. It also covers the question no competitor answers: which of these actually fits your camera body and your specific helmet, and which one you will regret when the strap catches your visor at 70mph.
A quick note before we start, because it changes what you should buy. If you are still choosing the helmet itself, our motorcycle helmet roundup for adults is the right place to start, and our action camera roundup for adventure travel covers the cameras themselves. Mount choice depends on both, so buy the helmet first and match the mount second.
Table of Contents
Top 3 Best Action Camera Mounts for Helmets in October
Lupholue Helmet Chin Strap Mount
- Strap and buckle chin attachment
- Silicone base
- No helmet modification
- Broad camera compatibility
Dango Design Gripper Mount
- Torsion spring gripper jaws
- Adhesive free
- Clamps objects up to 2.5 inch
- Leash and thumb screw included
TELESIN 180-Degree Chin Mount
- 180 degree flexible adjustment
- Food grade silicone base
- Reusable fixing tape
- Reversible camera adapter
Best Action Camera Mounts for Helmets in 2026
| Product | Specifications | Action |
|---|---|---|
| Lupholue Motorcycle Helmet Chin Strap Mount |
|
Check Latest Price |
| Dango Design Gripper Mount |
|
Check Latest Price |
 Sametop Helmet Sticky Mount Set |
|
Check Latest Price |
 MotoRadds Flex Slim Chin Mount Kit |
|
Check Latest Price |
| TELESIN 180 Degree Chin Mount |
|
Check Latest Price |
 TELESIN Chin Strap Mount with J-Hook |
|
Check Latest Price |
 Lupholue Chin Mount Kit with Curved Pads |
|
Check Latest Price |
 Insta360 Flexible Adhesive Mount |
|
Check Latest Price |
 SEASKY A1 Flexible Adhesive Mount 2-Pack |
|
Check Latest Price |
 K&F CONCEPT Chin Strap Mount |
|
Check Latest Price |
 Haoyou Helmet Chin Mount Strap |
|
Check Latest Price |
 Kewig Universal Chin Camera Mount |
|
Check Latest Price |
Chin, Top or Side: Where to Mount a Camera on a Helmet
Position decides the footage, and position decides whether the camera is still attached at motorway speed. Riders on r/gopro describe the chin position as the one that produced the best results for their POV footage, and that matches what you see in the wild: chin-mounted cameras point where you look, sit below the airflow, and barely move.
A chin mount sits low and forward, roughly in line with your eye line, which cuts frontal surface area dramatically and with it the sail effect that makes top-mounted cameras buffet at speed. The trade-off is access: on some full-face designs, chin strap routing stops the visor sealing completely, and that shows up as extra wind noise on the recording.
A top mount is the easiest install and the worst aerodynamics. It sits in the turbulent air just above the shell, catches crosswinds and produces visible shake on broken surfaces. Riders who want insurance-grade documentation rather than cinematic footage often choose it anyway because it never interferes with visor operation.
A side mount splits the difference. It frames a little wider, catches more of the road behind you for a sense of speed, and is less exposed to wind noise, but it cannot be aimed after installation without pulling the pad and re-seating it.
Two rider situations change the answer. If you switch helmets often or share one helmet between two cameras, a snap-fit or magnetic quick-release base beats any strap, because the swap takes seconds instead of a roadside re-strap. If you ride a bicycle rather than a motorcycle, weight matters more than drag, which favours the lighter flexible bases in this list.
1. Lupholue Motorcycle Helmet Chin Strap Mount – the Non-Permanent All-Rounder
Lupholue Motorcycle Helmet Chin Strap Mount Compatible with GoPro Hero 13, 12, 11, 10, 9, 8, 7, (2018), 6, Hero Black, DJI Osmo Action 5 pro/4/3/2,Insta360 ONER AKASO Campark YI and More（Black）
Strap and buckle chin attachment
Silicone base, 1.76 oz
69 g load capacity
Not water resistant
Pros
- Silicone base conforms to curved helmet surfaces
- No permanent modification to the helmet
- J-hook accepts a wide range of standard accessories
- Broad GoPro and DJI Osmo compatibility
Cons
- Loose strap ends rub the chin until trimmed or tucked
- Visor cannot seal completely
- Base sits loose on very pointed chins
This is the strap chin mount with by far the largest review base in the group, and that volume matters because the failure modes are well documented rather than anecdotal. The silicone base stretches to follow the shape of the chin bar, the woven belt tightens through a buckle, and the whole assembly weighs 1.76 ounces with a stated load capacity of 69 g.
The install takes about a minute with no tools and nothing stuck to your shell. That reversibility is the real argument for it: when you sell the helmet, change the camera or just get tired of the angle, you unclip it and the paint is exactly as it was. Riders who move cameras between helmets described that as the deciding factor for them in forum threads.
The 3.5 inch arm and the J-hook base give more reach than a bare chin plate, which lets you nudge the camera down or forward if your helmet’s eye line sits high. Compatibility is the broadest we found on any strap mount: GoPro Hero 13 down through Hero 3, Session, DJI Osmo Action 5 Pro and 4 and 3 and 2, Insta360 ONE R, AKASO, Campark and Yi cameras.
Two practical notes from the reviews. The strap tails are long enough to hang against the jaw unless you trim them or tuck them into the cheek padding, and the routing does stop a full-face visor closing all the way, so expect a little wind noise in the audio track.
One buyer also flagged that the base can sit slightly loose on helmets with a very pointed chin, since the silicone has less surface to grab. If your helmet is aggressive in shape rather than round, test it on the bike first.
When this mount is the right call
Choose it if you ride more than one bike or more than one helmet, or if you plan to sell the helmet eventually. Nothing is bonded on, and the swap between two cameras takes seconds.
It also suits open-face and three-quarter helmets, where a rigid chin plate has nothing to clamp to and a strap around the strap anchor is the only way to get a chin-level angle.
When to skip it
Skip it if you care about wind noise in your recordings, or if you ride at motorway speeds with a full-face visor and want it sealed. Riders on r/MotoUK threads about clip and buckle breakage should treat that as a reason to choose a metal or spring-loaded mount instead.
It is also not water resistant by specification, so leave it off if you expect to be submerged or washing the helmet with the mount fitted.
2. Dango Design Gripper Mount – the Clamp That Needs No Adhesive
Dango Design Gripper Mount for GoPro/Osmo/Insta360 | Universal Helmet Clamp Mount for Action Cameras | Dirtbike, Motocross, Enduro, Motorcycle, and ATV Helmets | Stealth Black
Twin torsion spring gripper jaws
3 oz, 5 x 2.75 x 2.75 inch
Waterproof
1 year warranty
Pros
- Twin spring jaws grip irregular chin guard shapes
- Nothing is stuck to the helmet
- Clamps objects up to 2.5 inch thick
- Leash
- thumb screw and extension included
Cons
- Bulkier and pricier than strap or adhesive mounts
- Spring force is fixed and weaker on thin chin bars
- Some frames need the thumb screw to sit level
This is the highest-rated mount we tested, sitting at 4.6 stars across 2380 reviews, and the mechanism explains why. Instead of adhesive or webbing, a pair of torsion-spring jaws close around your chin bar and hold by mechanical force, which means the helmet is never modified in any way.
The front webbing on the jaws flexes, so the clamp conforms to rounded, faceted and oddly shaped chin guards rather than needing a flat pad. Rated waterproof at 3 ounces, it is a natural fit for motocross, enduro, ATV and snowmobile helmets where the chin bar shape is unusual and adhesive pads would be the weak link.
Owners like that it does double duty. The same jaws clamp onto any object up to 2.5 inch thick, so it becomes a handheld stabilizer or a mini tripod when you are off the bike. The box also includes a safety leash for aggressive riding, a thumb screw for the camera interface, and a short extension for reach.
There is a real cost to that versatility. It is the bulkiest item here and the most expensive, which is a hard sell to someone who just wants a quiet, invisible chin plate. The spring is also a fixed force, so on a slim, open-face chin bar the grip is noticeably weaker than on a full motorcycle shell.
If your camera frame sits at an odd angle, expect to use the supplied thumb screw. It is a small adjustment that most owners make once and never think about again.
What you gain by going mechanical
The clamp holds a constant bite regardless of temperature, humidity or how long the ride is, which removes the entire question of whether a pad will creep. It is also the easiest mount to move between helmets, since you simply open the jaws and re-close them.
If you ride in rain, mud or snow, a waterproof clamp that rinses clean beats an adhesive base that has to survive being washed at the end of every ride.
Where the money and the bulk go
You are paying for a mechanism, not a piece of plastic and tape, and it shows in the packaging and in the size under your chin. Riders chasing the lowest possible wind profile on a street bike will find a slim strap mount looks and feels better.
Thin chin bars are the one case where it underperforms, so check the bite on a slow ride before you commit to it for a trip.
3. Sametop Helmet Sticky Mount Set – the Adhesive Bench
Sametop Helmet Sticky Mounts Adhesive Buckle Mount Accessories for GoPro
Genuine 3M VHB 4991 adhesive
140 g, plastic and steel
Waterproof
One year warranty
Pros
- Genuine 3M VHB adhesive on a plastic base
- Locking plugs cut accidental release and vibration
- Three curved plus three flat pads in the box
- Works with any finger or 1/4 inch camera
Cons
- Permanent and needs heat to remove
- Requires 24 hours in a warm place before loading
- A fixed base cannot be repositioned without a new pad
This is not one mount but a working set, and that is why it rates 4.6 stars over 1261 reviews. You get three curved adhesive bases, three flat bases, two horizontal quick-release buckles, two vertical J-hooks and two long thumb screws, all built on genuine 3M VHB 4991 pads with a plastic base.
The curved and flat split is the practical part. A flat pad on a rounded shell bridges the gap and peels at the corners; a curved pad follows the shell and spreads the load. Having both in the box means you can match the pad to whatever helmet you actually own rather than guessing.
The rubber locking plugs on the buckles are a small detail that matters more than they sound. They stop a quick-release popping open over bumps and they take up the slack so the camera does not rattle, which is the main source of the low-frequency wobble that makes footage look amateurish.
Compatibility is broad: GoPro Hero 13 down through Hero 1, Session and Max, plus DJI Osmo, AKASO, SJCAM, APEMAN and Campark bodies. Because it uses the finger and 1/4 inch interfaces, it is not tied to one camera brand at all.
Plan around the cure time. The instructions call for firm pressure and at least 24 hours in an environment above 10 degrees before the mount is load-bearing, and removal needs a hair dryer or heat gun to soften the pad. That is the price of a genuinely strong bond.
Why buy a set rather than a single pad
A two-position setup is what this kit is really for: one camera on the chin or top for riding, and a second on the side for a different angle. Riders who shoot the same ride from two viewpoints otherwise end up re-peeling and re-bonding between every outing.
It also solves the replacement problem. When a curved pad finally ages out or you sell the helmet, you already have spares rather than starting over from scratch.
Where this approach fails
It is a permanent commitment. If you are the kind of rider who changes helmets every season or borrows bikes, an adhesive base is a commitment you will resent. The 24 hour wait also means a mount applied before a trip is often not ride-ready for that trip.
A fixed base cannot be re-aimed. Get the angle right the first time, because correcting it means a new pad and a new 24 hour wait.
4. MotoRadds Flex Slim Flexible Chin Mount Kit
MotoRadds Flex Slim Flexible Universal Motorcycle Helmet Chin Mount Kit Bendable Silicone Compatible with GoPro Hero 12, 11, 10, DJI Osmo Action, Insta360, SJCAM, Xiaomi Yi Action Cameras (Black)
Flexible silicone chin base
0.06 kg, 59 g capacity
Water resistant
Rotatable
Pros
- Silicone base molds to curved chin bars for low vibration
- Rotatable adjustment dials in the camera angle
- Very light at about 60 g
- No adhesive involved
Cons
- Lowest average rating in this roundup with a 15 percent one-star share
- Silicone can creep on bumpy terrain
- Can block the chin vent or visor closure
The MotoRadds Flex is a pure flexible silicone chin mount with no adhesive, and at roughly 60 g it is among the lightest options here. The mouldable base wraps a curved chin bar and the rotatable joint lets you set the camera angle without re-fitting the mount.
Owners generally like the framing it produces on round street helmets, and the fit works across motorcycle, mountain bike, slopestyle, motocross and snowmobile shells. It also works with a wider range of bodies than most chin mounts, including some phones.
It also has the weakest rating of the twelve at 4.1 stars, with a 15 percent one-star share, and the complaints are consistent rather than random. The silicone pad can creep over time on rough terrain, which means the mount slowly needs re-seating, and on some full-face designs the base can sit near the chin vent or stop the visor closing cleanly.
The price is the other sticking point. Buyers repeatedly note that you are paying a premium for what is fundamentally a simple flexible chin mount, and the most common defence is that the fit and angle adjustability justify it on their particular helmet.
If you ride on chip seal or broken tarmac and never re-check your mount, a fixed mechanical clamp will serve you better over a season.
Where flexible silicone earns its keep
Silicone is the quietest material against a shell. It does not scratch paint, it does not transmit the sharp buzz that hard plastic does, and it absorbs enough high-frequency vibration to keep your footage from shimmering on rough surfaces.
It is also the lightest option for riders who care about what the mount adds to their head. At about 60 g you will forget it is there after the first few minutes.
When the rating shows through
Buyers report gradual loosening, so treat this as a mount to check at every fuel stop rather than fit-and-forget. If you ride in rain, note the listed rating is water resistant rather than waterproof.
It is also the pick to avoid if your helmet has a pronounced centre crease. A flexible base moulds to a ridge rather than bridging it, and a rigid plate or a clamp handles that geometry better.
5. TELESIN 180-Degree Chin Mount
TELESIN 180° Adjustable Motorcycle Helmet Chin Mount for Action Cameras
180 degree flexible adjustment
Food grade silicone base
2.88 oz, 80 g capacity
Water resistant
Pros
- 180 degree adjustment suits round and angular helmets
- Food grade silicone is comfortable and grips well
- Fixing tape is reusable many times
- Camera adapter flips for either orientation
Cons
- Straps stop the visor closing fully and can tickle
- Plastic tabs can crack on open or unsupported chins
- Some units arrived without the J-hook
The TELESIN 180 is the mid-budget chin mount that solves the framing problem properly. The joint flexes through a full 180 degrees, so the same mount fits a round street helmet and an angular racing shell without changing the position of the base on the chin.
At 2.88 ounces with an 80 g load capacity, it is heavier than the cheapest strap mounts but well within what a full-face helmet will carry without complaint. The food grade non-slip silicone sits against the chin without grabbing skin, which matters on a long ride.
Two design decisions stand out. The fixing tape is rated as reusable many times over, so unlike an adhesive pad you can take this off, re-seat it and put it back. The camera adapter also flips upside down, which lets you mount a camera that needs a specific orientation for its buttons or ports.
Durability is the strongest part of the review set. Owners report it surviving mountain bike crashes and around a year of daily commuting without loosening, and the water resistance rating covers ordinary wet-weather riding.
The complaints are physical comfort ones. Straps routed through the chin bar stop the visor closing completely, and untucked strap ends can brush the face. On a helmet with an open or unsupported chin, the plastic support tabs are the stress point and can crack under a hard landing.
Keep a thumb on that as the one thing to check after a crash, and if you want a mechanical guarantee of retention, this is not the mount family for you.
Who should buy this one
Buy it if you ride a mix of street and track-style helmets, or if you swap between an angular MX shell and a round street shell. The 180 degree range is the feature you will use most and the reason most reviewers are happy at 4.4 stars.
It is also a sensible first chin mount for a commuter who will not fit an adhesive pad but wants an angle they can fine-tune after a few rides.
What to check before ordering
Read the box contents carefully. A number of buyers reported units arriving without the advertised J-hook, and that part is what attaches to most GoPro-style fingers, so confirm it is in the pack before you start.
If your visor is already tight, test the strap routing on the bike. A mount that stops the visor sealing is the most common reason people return these, and no amount of angle adjustment fixes it.
6. TELESIN Chin Strap Mount with Extension J-Hook
Helmet Mount for GoPro, Motorcycle Chin Strap Attachment with Extension J Hook Dirt Bike Holder Mounting Accessories for Go Pro Max Hero 13 12 11 10 9 8 Insta360 X5 X4 DJI Osmo Nano Action 3 4 5 Pro 6
Extension J-Hook base
80 g, water resistant
180 degree adjustment
ABS Y-shape base
Pros
- 180 degree adjustment across round and angular shapes
- Soft silicone pad avoids scratching the shell
- Extension J-hook adds reach for finer angles
- One hand install and removal
Cons
- Rotation selector can shift under rough riding
- Straps interfere with the visor seal and modular releases
- Some bodies need a frame case
This is the dirt bike answer in the roundup. Rather than a bare chin plate it uses a high quality ABS Y-shape base with rounded edges, a soft non-slip silicone contact face and an extension J-hook that adds reach beyond the strap length, so you can bring the camera down or forward for a lower, more natural POV angle.
Owners consistently praise the natural chin-mounted framing and the grip of the silicone, which stays put when a motocross helmet is being thrown around. Install and removal are one-handed, which matters when you are strapping in at a track or in a car park with gloves on.
The silicone also means it will not scratch the shell, which is a genuine concern on the graphics-heavy lids that MX riders tend to own. Compatibility runs from GoPro Hero 13 down to Hero 5 and Session, through DJI Osmo and Action models, to Insta360 X and Go bodies.
Where it gets less convincing is on very rough terrain. Several reviews report the rotation selector or the base itself shifting once the straps are loaded, and the elastic strap routing interferes with the visor seal and, on modular helmets, with the chin strap release mechanism itself.
That last one is a genuine safety consideration rather than a comfort complaint. If your helmet is modular, confirm the release lever stays fully operable before you rely on this mount.
What it does for off-road riding
A longer reach and lower camera position changes the footage more than any resolution upgrade. On a dirt bike, that gives you a view of the front wheel and the line you are taking, which is the footage people actually buy this mount to capture.
The rounded Y-shape base also spreads pressure away from the sharp centre crease that some MX and adventure helmets have, which is where a lot of generic chin mounts fail.
Where it needs attention
Check the rotation selector after hard hits and at every fuel stop. Shift under load shows up as a camera that slowly points at the sky, and on a rough track that can happen inside a single session.
Some camera bodies also need a frame case or an extra adapter that is not in the box, so confirm the interface before you commit.
7. Lupholue Chin Mount Kit with Curved Adhesive Pads
Lupholue Motorcycle Helmet Chin Mount Kits with Adhesive Curved Pads Compatible with DJI Osmo Action 6, Osmo Action 5 Pro, Osmo Action 4, Osmo Action 3, Insta360, AKASO, GoPro (Version A)
Curved and flat adhesive pads
2.08 oz, 5.12 x 4.72 x 0.79 inch
Waterproof
1 year warranty
Pros
- Enlarged adhesive area steadies the footage
- Flat and curved pads both included
- Handles long and short chin geometries
- Buckle sticker and rope backup included
Cons
- Pads bond permanently and need heat to remove
- Backup hardware adds bulk under the chin
- Effectiveness depends on surface curvature and prep
This is the adhesive route to a chin position, and the improvement over cheap adhesive chin mounts is the enlarged bonding area. A larger pad spreads the camera load across more of the shell, which is what stops a chin camera from vibrating itself loose over a long ride.
Both flat and curved pads are included, so you can match the pad to your shell the way you would with the Sametop set, and the arm adjusts up and down to suit long chin and short chin geometry. That is genuinely useful if you are not sure how much chin bar your helmet has.
It is also one of the few chin mounts that ships with real backup. A buckle sticker and a hanging rope are included as a second line of defence, so even if the pad lets go the camera does not simply depart down the road. An extension arm is also in the box for shooting from a different angle.
The catch is that all of it is fixed. Adhesive pads bond permanently and need heat to remove, the extra hardware adds bulk under the chin where there is very little room, and how well it holds depends heavily on the curvature of the shell and how thoroughly you cleaned it first.
At 553 reviews the feedback set is smaller than the strap mounts, so the long-term data is thinner here. That is worth knowing rather than worrying about.
When adhesive is still the right answer
Choose adhesive when the camera never moves between helmets and you want the lowest possible profile. There is no strap under the chin, no buckle to catch, and nothing that can work loose over a long trip.
The included buckle sticker and rope also make it the safer adhesive option, because a failure does not automatically mean a lost camera.
When to buy something else
Skip it if you change helmets, lend your gear to friends, or expect to resell the shell. Removal takes a heat gun and can leave a mark or residue on some finishes, which is the single most common complaint about every adhesive mount in this category.
Also skip it if your chin has a deep centre crease. A curved pad cannot bridge a ridge, and a rigid plate or a clamp mount is the correct tool for that shape.
8. Insta360 Flexible Adhesive Mount
Insta360 Flexible Adhesive Mount
Flexible base, 82.8 g
3M adhesive base, heat resistant
Two mounts plus adapter
Pros
- First party mount with a strong 3M adhesive base
- Flexible design fits flat and curved surfaces
- Owners report it staying bonded for months
- Two mounts and a 1/4 inch to two prong adapter included
Cons
- Adhesive is very hard to peel off and needs heat
- Listed as not water resistant despite outdoor use
- A surface mount commits you to one helmet position
The Insta360 is the one first-party mount in this group, and that matters for 360 bodies. It is designed around the camera that needs it, with a flexible base and a 3M adhesive core rated for heat and humidity, which are the two things that destroy a cheap pad on a helmet.
It carries an 81 percent five-star share, and the reviews are close to unanimous on bond strength. Owners report months of attachment and no movement through high-speed and harsh conditions, on everything from race cars and motorcycles to hard hats and even rolled-up packrafts.
The pack includes two flexible mounts and a 1/4 inch to two-prong adapter, so you can fit the camera directly or route it through other accessories. At 82.8 g it is the heaviest mount here, which is a fair trade for the camera itself sitting on top of it.
Because the camera has to point somewhere specific, the two included mounts let you cover a second angle without buying another pack, and on a 360 body you can reframe the shot in software either way.
The specification lists this mount as not water resistant. The adhesive handles heat and humidity well, but do not submerge it and do not assume the base is sealed. As with every adhesive mount, removal needs heat and the bond is strong enough to be frustrating on glossy shells.
Why first-party matters for 360 cameras
A 360 body is heavier and larger than a GoPro-style action camera, and it needs to sit in a predictable orientation for reframing to look right. A mount designed for that specific body gets the hinge geometry and the load path right instead of approximately right.
The included 1/4 inch to two-prong adapter is the detail that confirms it. It was made to bridge the 360 world and the accessory world rather than just to hold one camera up.
The trade-offs to accept
You are committing to one position on one helmet. If you switch helmets or want to remove the mount for a resale, you are peeling 3M off a curved shell, which is the least pleasant task in this entire roundup.
Check the not water resistant line before you commit, particularly if your riding involves river crossings or heavy spray.
9. SEASKY A1 Flexible Adhesive Helmet Mount 2-Pack
SEASKY 2Pack A1 Flexible Adhesive Helmet Mount use Genuine 3M Adhesive
Semi flexible TPU base, 0.14 kg
500 g capacity
Two mounts and two adapters
Pros
- Larger base area than typical adhesive mounts
- Semi flexible TPU underside grips curved shells
- Genuine 3M adhesive rated for temperature and humidity
- Two pack allows two cameras or two helmets
Cons
- TPU tabs can snap under load so use a leash
- One report of the mount releasing mid ride
- Permanent attachment
The SEASKY A1 is the one to look at if you want two cameras or want the same mount on two helmets. The pack includes two flexible adhesive mounts and two 1/4-20 adapters, so you can run a front and a chin angle, or a camera on each bike.
The design choices are deliberate. The base area is larger than a standard adhesive mount, and the underside is semi-flexible TPU rather than rigid plastic, so it follows a curved shell instead of bridging it. The 1/4-20 thread also opens compatibility to 360 and panoramic bodies, not just finger-mount action cameras.
Owners mostly agree the adhesive is very strong and long-lasting for casual riding, with several reporting two or more years on a helmet with no peeling. It handles GoPro Hero 13 down to Hero 8 including Max, DJI Action models and Insta360 X and Ace Pro bodies.
The reviews split on the base itself rather than the glue. Several accounts describe snapped TPU tabs or a mount coming unstuck, and there is one report of it releasing mid-ride after a short trip. That is why we would run a safety leash on this one every time, whatever the adhesive is doing.
It is not the mount for a rider who rides hard on rough surfaces at track speeds and never checks their hardware. It is well made and well priced for what it is, but the material it uses is a compromise against impact rather than a strength.
What the two-pack actually unlocks
Two cameras on one helmet is not a gimmick. A forward-facing body records the ride and a second body pointed at the rider captures the follow shot, or you can run one for video and one as a rear view. It also means a spare mount on a second bike, which is where most riders get real value from a two pack.
The 1/4-20 adapters also make it the flexible option if you swap between a standard action camera and a 360 body.
Honest durability picture
This is where we would temper expectations. The adhesive is excellent, the TPU tabs are the weak link, and a snapped tab means a camera in the road. Tether it, inspect it after any off, and do not treat it as a track-day mount.
Peeling it off is a job. Plan on a heat gun and a patient twenty minutes if you ever want the shell back.
10. K&F CONCEPT Chin Strap Mount
K&F CONCEPT Action Camera Motorcycle Dirt Bike Helmet Chin Strap Mount
ABS Y base with rubber backing
Adjustable tilt arm
Not water resistant
Two-claw and 1/4 screw fit
Pros
- Extended straps and upgraded quick-release lock
- ABS Y base with rubber backing avoids scratches
- Dual buckle lock prevents loosening
- Tilting arms set the recording angle
Cons
- Straps prevent full visor closure and add wind noise
- Fit varies widely by helmet shape
- Not water resistant
- Rubber backing and ABS add bulk under the chin
The K&F CONCEPT mount is a straight strap chin mount with an unusually well thought-out locking mechanism. The dual buckle lock is the difference between a mount that stays put and one that creeps, and buyers specifically call out the stable footage and the absence of screen shake as the reason it holds up.
The Y-shaped ABS base is styled to follow the chin and the rubber backing sits between the plastic and your shell, so it will not scratch the paint. The arms tilt to set the recording angle, and the quick-release buckle strap fits different chin shapes without tools.
Compatibility is broader than the shape suggests. Any camera using the two-claw interface or a 1/4 inch screw fits, and the spec sheet names full-face, motorcycle, mountain bike, dirt bike, slopestyle, motocross and snowmobile helmets.
The drawbacks are the same ones that come with any strap routing. The straps stop the visor closing fully, which produces heavy wind noise on the audio, and the fit varies a lot by helmet shape: smoother, rounder shells are the hardest for a strap mount to hold onto.
It is also not water resistant, which matters for snow and mud work. At the bulk end, the rubber backing and ABS body add a noticeable lump under the chin compared with a bare silicone pad.
Why the buckle detail matters
A strap chin mount fails in a specific way: the buckle creeps, the tension drops, and the camera starts to move. Once a camera moves you get the low-frequency wobble that no amount of stabilisation in software will fix, plus a rising risk of it coming loose entirely.
The dual lock on this mount is the least you can do to protect against that failure, and it costs nothing extra at the point of purchase.
Where the fit will frustrate you
Try it on your actual shell if you can. Riders with smooth, rounded chin bars report the least secure hold, and a helmet with a pronounced centre crease is a poor match for a strap that expects a flat-ish band.
For snow and water work, treat it as a dry-weather mount and dry it before storing.
11. Haoyou Helmet Chin Mount Strap
Haoyou Helmet Chin Mount Strap Compatible with Gopro Hero 13 12 11 10 9 8 7 and DJI Osmo Action Camera，Motorcycle Helmet Extension Attachment Mounting Accessories (Black)
180 degree angle adjustment
1.76 oz, 4.12 x 3.75 x 1.8 inch
Short and long arms
1 year warranty
Pros
- Lowest cost in the roundup with 180 degree adjustment
- Long and short extension arms vary the angle
- Anti-slip anti-shock silicone protects the shell
- Reusable and easy to disassemble
Cons
- Long straps need tucking to stop face contact
- Straps can stop the visor or windscreen closing
- Some users report the mount moving over time
- Cheap plastic buckles wear with extended use
The Haoyou strap is the cheapest way into a proper POV chin angle, and the surprising part is how much adjustability you get. It adjusts up and down through 180 degrees and the box includes both a long and a short extension pivot arm, which is more range than several mounts twice the price offer.
At 1.76 ounces it is among the lightest we tested, and the silicone base has anti-slip and anti-shock particles worked into it, so it grips the shell without damaging the surface. Install and removal take seconds, and the whole thing disassembles for reuse.
Owners call it excellent value, and the fit on motocross helmets with unusual chin shapes comes up repeatedly as a positive. Compatibility covers GoPro Hero 13 through 7, DJI Osmo Action 6 through 3, Insta360 X and Go bodies, AKASO EK7000 series and similar cameras.
The strap tails are the recurring minor issue. They are long enough to need tucking behind the buckles to stop them rubbing the face on a long ride, and they can stop the visor or a windscreen from closing completely.
Two other reports are worth weighing. Some users say the mount gradually moves around and loses stability over time, and the plastic buckles are the component most likely to need replacing after extended use. Neither is a dealbreaker at this level, but both argue for a routine check rather than a fit-and-forget approach.
What you get for very little
Real angle control at this level is unusual. The combination of 180 degree adjustment and two extension arm lengths means you can move the camera from a tucked-under-chin angle to a forward and low position without buying a different mount.
The anti-slip silicone also makes it a reasonable choice for a helmet you care about, since it will not scratch the shell the way bare ABS can.
Where to spend a little more
If you ride at motorway speeds daily and care about wind noise in your recordings, the strap that stops the visor sealing is the deal-breaker rather than the price. Every strap mount in this roundup has that limitation.
If retention under rough terrain matters more than cost, a clamp or spring mount holds more predictably than any buckle. Budget for a leash either way.
12. Kewig Universal Chin Camera Mount with Quick Release
Kewig Universal Motorcycle Helmet Chin Camera Mount, Quick-Release Design
Snap fit quick release
60 g, PA66 plus glass fibre
Waterproof
Backup pads and tether included
Pros
- Bendable base fits most full-face chin shapes
- Snap fit design removes the camera in seconds
- Two tripod adapters give 180 degree adjustment
- Includes spare adhesive pads and a safety tether
Cons
- Adhesive pads are permanent and need heat to remove
- Requires 24 hours before the mount is loaded
- Cannot be used over a screen protector
- Smallest review base in the roundup
The Kewig is the mount for the shared-helmet problem. The camera attaches to a snap-fit tripod adapter and comes off in a couple of seconds, so two riders can swap cameras at a fuel stop, or you can move a body between a bike helmet and a spare without re-strapping anything.
The base itself bends to fit most full-face chin shapes, and it weighs about 60 g in glass-reinforced PA66, which is stiff enough to hold an angle without adding meaningful weight. The whole unit is rated waterproof.
The box is unusually generous for a mount at this level: a bendable mounting base, two tripod adapters, an Allen wrench, two sets of strong adhesive pads and a safety tether. The spare pads matter more than they look, because if the first set ages out you are not starting from nothing.
Compatibility covers GoPro Hero 13 through Hero 1 plus Session and Max, Insta360 X, ONE RS, Go Ultra and Ace Pro 2, and DJI Osmo 360, Action 6, 5 Pro, 4, 3 and Nano.
It is also the newest listing here with 84 reviews and an 83 percent five-star share, which is a small enough sample that long-term durability data is limited. Buyers like the quick-release convenience, the bendable base fit and the backup pads, while the adhesive commitment and the 24 hour settling time are the stated cautions.
It cannot be used on a helmet with a screen protector under the bonding area, which is worth checking if you use one.
Why quick release changes the use case
A quick release only matters if you actually swap. Riders who share one helmet between two bodies, or who run a camera on a bike and a phone camera on a scooter, save several minutes and a lot of fumbling every single time.
It also makes a second body practical. Leave a body permanently mounted and swap to a fresh one on long trips, which is exactly how a failed battery becomes a lost clip instead of a lost ride.
What you still have to live with
The base is adhesive, so you are committing to one helmet position and a 24 hour wait before the first loaded ride. Follow the maker’s guidance: warm the pad briefly with a hair dryer, press it, leave it, and use the tether.
With 84 reviews you should treat the long-term picture as still forming, and check the base and the tabs every few rides for the first season.
How to Stick a GoPro Mount to a Helmet in Five Steps
Adhesive mounts fail for boring reasons: dirty shells, rushed cure times and too little pressure. The sequence below is what the mount manufacturers themselves specify, and it works.
Clean the bonding area. Wipe the shell with isopropyl alcohol to remove wax, polish and road film. The pad bonds to a surface, not to a layer of grime, and this is the step that most often gets skipped.
Warm the surface and the pad. A hair dryer for around 30 seconds raises the shell temperature and makes the pad conform more closely. Cold shells give you a weaker bond and a slower cure.
Choose the pad shape deliberately. A curved pad for a rounded shell, a flat pad for a flat panel. Bridging a curve with a flat pad is the most common cause of a corner lifting and peeling.
Press hard, then wait. Apply firm pressure for at least 30 seconds, then leave the helmet in an environment above 10 degrees for a full 24 hours before the mount carries any load. Sametop and Kewig both specify this cure window explicitly, and riding before it has elapsed is the most reliable way to lose a camera.
Fit the tether. Run the safety lanyard from the camera to a strap or a fixed point on the helmet. Riders almost universally treat this as non-negotiable, and several of the mounts in this roundup ship with one for exactly that reason. A tether costs nothing and covers the one failure mode that ruins the ride.
Removing an adhesive base later is the reverse: soften the pad with a heat gun or hair dryer and peel slowly, working the edge rather than pulling straight off. Expect a mark or a little residue on glossy shells, and decide before you stick rather than after.
What to Look for When Buying a Helmet Mount
Start with your helmet, not the mount. Full-face street, modular, MX and dirt, open-face, bicycle and 360 helmets all have different chin bars and different amounts of usable shell. Strap and clamp mounts need a chin bar to hold on to. Adhesive and top mounts need a flat or gently curved patch of clean shell, and a helmet with a deep centre crease defeats most universal chin plates.
Then check the camera interface. Most mounts here accept the two-claw finger interface, which covers GoPro Hero, DJI Osmo Action and a long list of AKASO, SJCAM and Campark bodies. The 1/4-20 screw interface is what opens compatibility with 360 and panoramic cameras, so if you run an Insta360 X-series or GO body, confirm the mount includes the adapter. The Insta360 first-party pack and the SEASKY two-pack both ship the adapter; some cheaper kits list camera models without including the part needed to mount them.
Decide how permanent you want to be. Nothing stuck to the shell means you can change your mind, move the camera and resell the helmet clean. Adhesive means a lower profile and better vibration behaviour, plus a commitment and a possible mark at removal. Riders who switch helmets often should stop at the strap or clamp end of the list.
For bike riders, weight outranks drag. A bicycle helmet sees far less wind load than a motorcycle at speed, so the 60 g flexible mounts make more sense than they would on a bike, and the strap and adhesive families are largely interchangeable. Pick the lightest thing that will hold on rough ground, and skip anything with an adhesive tab that could crack. If you are shopping for the rider rather than the bike, our kids bike helmet guide covers fit for younger riders.
What to avoid. Treat 3D-printed chin mounts with caution rather than dismissal. Printed parts exist and some work, but UV exposure and weather degrade the plastic at exactly the stress points, and the failure tends to be sudden. Unbranded marketplace mounts with no support and thin buckles are worse, because the buckle is the part that carries the shock. Stick to a named brand with a published warranty, and always run a tether whatever you buy.
Finally, buy the camera first. It is far easier to choose a mount that suits a body than to find a body that suits a mount you already own. Our action camera roundup is the place to settle that question first.
Helmet Safety: Never Drill, Check Impact Zones, Always Tether
Never drill a helmet. Modifying the shell can compromise the liner and the shell bond, and it will affect how the helmet performs in an impact. Every mount in this roundup attaches with adhesive, straps, clamps or a base plate for that reason, and you should treat any seller offering a drilled fitting as a red flag.
Keep the camera and its base out of the impact zones. Manufacturers describe the regions of a shell where damage and deformation are most likely to affect protection, and a raised mount or a hard buckle sitting in one of those areas is both a safety problem and, in some crash tests, a legality problem. Low and forward on the chin bar is generally the safest place, which is another argument for the chin position over the top.
Check visor clearance before you commit to a strap mount. Fit the straps, close the visor fully, and confirm it latches or seals. On modular helmets, make sure the chin strap release lever still operates freely. Several reviewers returned mounts over exactly this issue.
Run a tether, every ride. Riders describe losing cameras at speed as the one outcome nobody volunteers for, and a lanyard from the camera to the helmet turns a total loss into an inconvenience. Several mounts here ship with one.
On legality, rules vary by country, state and riding discipline, so check your local regulations rather than taking anyone’s word, including ours. What is broadly consistent is that a camera mounted on your own helmet is treated differently from one on someone else, and that footage you record may be used in an insurance claim, so aim it where it can actually see the road and the vehicle ahead.
Frequently Asked Questions
What is the best action camera mount for a helmet?
A chin mount gives the best POV framing and the lowest wind load, and it is the right answer for most riders. Choose a clamp mount if you will not accept any adhesive or strap on your shell, and a curved adhesive mount if you ride one helmet and want the lowest profile.
Where to mount an action camera on a helmet?
The chin bar for POV footage and low drag, the top for the easiest install and no visor interference, or the side for a wider framing that catches more of the road behind you. Chin positions cut frontal area dramatically, top mounts catch the most wind, and side mounts are hard to re-aim once bonded.
Are GoPro adhesive mounts strong?
Genuine 3M VHB pads on a rigid base hold a camera firmly, provided the shell is cleaned, the pad matches the curvature, and you give it the full cure time. Sametop and Kewig both specify at least 24 hours above 10 degrees before the mount is load-bearing, and both require heat to remove.
How do I stick a GoPro mount to a helmet?
Clean the shell with isopropyl alcohol, warm the surface and pad with a hair dryer for around 30 seconds, match a curved pad to a rounded shell, press firmly for 30 seconds, then wait at least 24 hours in a warm environment before riding. Fit a safety tether before the first ride.
Is it safe to mount a GoPro on a helmet?
It is safe when the mount is mechanical, non-drilled and positioned away from the shell’s impact zones. Never drill a helmet, keep rigid hardware off the crown and side impact areas, check visor operation and modular chin-strap releases, and run a tether so a failure does not drop the camera.
Is a GoPro on a helmet illegal?
Laws differ by country, state and discipline, so check your local rules. In general a camera on your own helmet is permitted, but a mount that obstructs your visor, mirrors your field of view or sits in an impact zone can be treated as a safety or modification issue.
Which Helmet Mount Should You Buy?
Our pick for the best action camera mounts for helmets overall is the Lupholue Motorcycle Helmet Chin Strap Mount, because it has the deepest review history in the group, attaches and removes in under a minute, and costs you nothing on your shell. If your objection is permanent modification rather than budget, the Dango Design Gripper Mount is the strongest option on grip, rated 4.6 stars over 2380 reviews, and it doubles as a handheld stabilizer off the bike.
Match the family to your riding instead: adhesive sets such as the Sametop kit for one helmet and one angle, flexible silicone such as the MotoRadds Flex for the lightest fit, the TELESIN 180 for genuine angle control, and the Kewig if you swap cameras between riders and need the camera off in seconds. Whichever you choose, run a tether, and give any adhesive pad the full 24 hours before it carries a camera.